Need XR parts asap

Driveing this car to Ontario end Dec so I need to get it sorted out.
I need...
-wastegate acuator
-cladding for dvr side
-decent winter tires
-after market guages, a/f,boost,temp,oil.
-good source for parts lol

I can help you with your need for parts. I'm assuming you're from edmonton. I have the cladding you want, but you'll have to re-rivet it back on, maybe fugu has a better solution to mounting that cladding.

I believe BRYXR4TI has a few wastegate actuators, i'll find out for ya. For the guages, i'd go to Best Buy Performance, they always seem to have the best prices. Winter tires? depends on how much you wanna spend. If you need any more XR specific parts let me know, we have XR parts out the yingyang here in edmonton.

Feel free to call me at (780) 634-6198 (home) or (780) 908-9500 (cell), just ask for Vaughn.

Thanks but I'll pass on the cladding cause I ripped mine off and I think it looks better. In dier need of that waste gate actuator.

sorry no actuators left you will have to get one from Russ 465-1050
Merkur Club Pres
as for tire i recomend Nokian rsi's awsome winter tire

I have a boost gauge if u would be interested, i bought it for my turbo swap on my mustang that never quit worked out, so its literly brand new, its the autometer Phantom series, and its 0-35 PSI, if ur interested just send mea pm and i'll get back to on it, maybe send u a pic:)

the best place it town to buy guages is usualy best buy performance

484-8220, very good people working there

How much for the boost guage?
I got a actuator!!
Would like a cosworth grill.

60$

Is that gauge a boost/vac guage or only boost?

I do have my spare autometer procomp "boost: gauge, no vac on that one though.
I have another wastegate actuator but it doesn't hold 15psi, it will function enough to allow the car to be driveable (holds the wastegate shut till you let off the throttle) I also have gaskets made up to remount the actuator.
The cladding? hmmm well it would have to be riveted back on obviously, if i knew the size of the original rivets and how they connect to the cladding then I could help.

unfortanitly its only boost, no vac, it just boosts to 35psi

I'll pass on the guage, I want one with vac.

Also would like a dash without cracks. :(

A dash without cracks... a hard find, i'm looking for one too. But they are out there. I'm gonna be calling Russ soon to see if he's got any.

just fiberglass the cracks up ;) lol

I think I am going to fibreglass my dash too. Why not, then it can be really customized! and any colour I want.
maybe I should nickel plate it?

I think I am going to fibreglass my dash too. Why not, then it can be really customized! and any colour I want.
maybe I should nickel plate it?
hell here is the deal.. vaughn gave he half the idea...
get a spair craked dash, peal the old surface off.. sand the sahpe you want , and the put a thin layer of fiberglas... resin.. boom.. no more cracks.


but that just an idea.. or you can pay 300$ fo an unkraked one

I think I am going to fibreglass my dash too. Why not, then it can be really customized! and any colour I want.
maybe I should nickel plate it?

Beware of the reflections off that thing.

Mine came with no cracks, but the thing that bugs me is that the defroster vents kinda suck so I'm thinking of removing those plastic vent covers to see if that helps.

Anyone got a spare 5 speed swap kicking around?

Anyone got a spare 5 speed swap kicking around?
vaughn does.

Anyone got a spare 5 speed swap kicking around?

I do.. and it's all ready to go! Gonna be pulling it out of my car in the next couple of days. Mines the full mustang T5 conversion kit, everything you need to bolt it into your car... New clutch, throwout bearing, rear tail seal, and a robs custom shifter included. About 3000km on the parts. My tranny came from an 91 mustang 2.3 with only 88000 km, so it's mint, shifts smooth, no grinds. Also comes with the galaxie1 t5 mounting kit, with new speedo cable, crossmember, and tranny mount. Give me a shout if you interested though.

I do.. and it's all ready to go! Gonna be pulling it out of my car in the next couple of days. Mines the full mustang T5 conversion kit, everything you need to bolt it into your car... New clutch, throwout bearing, rear tail seal, and a robs custom shifter included. About 3000km on the parts. My tranny came from an 91 mustang 2.3 with only 88000 km, so it's mint, shifts smooth, no grinds. Also comes with the galaxie1 t5 mounting kit, with new speedo cable, crossmember, and tranny mount. Give me a shout if you interested though.

If his car is an auto he is gonna need the clutch pedle assembly too !!!
mabey Russ can help him out there

Ok gents I need injectors ASAP!!!
Pulled mine out and I found the bogging problem(I think) One of my injectors had the top blown off.

Ok gents I need injectors ASAP!!!
Pulled mine out and I found the bogging problem(I think) One of my injectors had the top blown off.

I have a bunch of injectors are you in edmonton??

yup.
Send me your #